Bossarea Forum
Bossarea Forum
Home | Profile | Register | Serial Database | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 Other Products
 Non Boss Gear Discussions
 Tyra Banks - Pedal Board - not NAKED
 New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

Dr. Bob
Moderator

Australia
6593 Posts

Posted - 10/11/2009 :  09:56:35  Show Profile  Visit Dr. Bob's Homepage  Reply with Quote
What's this got to do with Tyra Banks not NAKED, & her pedal board?

Nothing really. --- I just couldn't think of a Good Title.
To be really honest, I don't even know if I posted it in the right section?

It's one of my project ideas.
I Just thought you guys might like to see, some of what I have been up to over the weekend.

A little while ago I went to the local recovery centre, Tip/Rubbish dump
I have written about this place a few times, it's a huge shed that
sells off items that are recovered from peoples hard rubbish, before it's bulldozed into the ground.

Well I found a Franklin Volleyball storage case, it looked like it might be usable as a pedal case.

I don't know what a new one of these kits sells for, but even if it was $50+,
it's still a lot cheaper than the $299au to $2349au;
That the Aussie music stores are asking for a Boss BCB-60,
and the $120au to $199au for a BehringClone PB600.

With the addition of a bit of protective upper foam,
and some stiffer lower foam (not yet attached) it would make a very nice MegaPeadCase.

Outside of case from hinge side, so you can read the label.


The inside of the case - with the bits that were in it when I bought it.


A few different ideas to show you how large this case is.

Nearly all Boss: even room for a TU-12


Variations:


More variations:


Like I mentioned, I just need to get some firm foam for the bottom of the case.
And a bit more protective ripple foam for the lid.

I have been thinking about adding some removable hinges,
and some Velcro or something similar, as safety snaps for the lid.

Overall, the case cost me a Whole "One" Dollar ($1) from the recovery centre.
The ripple foam came from some packing courtesy of work.
And I still have to beg - borrow or buy the other items.

For those that are wondering about the size:
Overall dimensions = 830mm x 260mm x 92mm

Regards Dr. Bob
Now --- about that subject title?

Edited by - Dr. Bob on 10/11/2009 10:30:16

zerksies
Double Platinum Member

USA
3406 Posts

Posted - 10/11/2009 :  15:07:29  Show Profile  Send zerksies an AOL message  Click to see zerksies's MSN Messenger address  Send zerksies a Yahoo! Message  Reply with Quote
that could be quite useful
Go to Top of Page

Laurie
Double Platinum Member

Canada
4854 Posts

Posted - 10/11/2009 :  18:11:50  Show Profile  Visit Laurie's Homepage  Reply with Quote
Cheap and cheerful Dr. Bob! Looks good to me!
Go to Top of Page

DeFrag
Moderator

USA
3409 Posts

Posted - 10/11/2009 :  20:28:53  Show Profile  Visit DeFrag's Homepage  Click to see DeFrag's MSN Messenger address  Reply with Quote
damn.. all I saw was NAKED.
Go to Top of Page

FRANZONI
Double Platinum Member

Ireland
3543 Posts

Posted - 10/11/2009 :  22:39:55  Show Profile  Visit FRANZONI's Homepage  Reply with Quote
Great find Dr Bob..... that title was a 100% way to get our attention.......
Go to Top of Page

hateandwar
Gold Member

Australia
524 Posts

Posted - 10/12/2009 :  08:24:19  Show Profile  Reply with Quote
nice work bob!
kinda like the homemade one i made out of an old bosch drill case haha
Go to Top of Page

TKO Ken
Silver Member

USA
162 Posts

Posted - 10/12/2009 :  23:02:04  Show Profile  Visit TKO Ken's Homepage  Reply with Quote
That's using your head man
I bet the latches will last longer than on the....... can't say it

How sturdy is it?? it looks a little on the thin side.

Edited by - TKO Ken on 10/12/2009 23:04:04
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
Bossarea Forum © 2005-2007 BossArea Go To Top Of Page
Powered By: Snitz Forums 2000 Version 3.4.06